What's new in version 1.0. What You Can Expect from Linux on your iMac G5This update improves performance and reliability of the Fan Control system of the Power Mac G5. Note: The LED on your power adapters might change states or temporarily turn off when you reset the SMC. 4) Reconnect the battery and power adapter and press the power button to turn on the Mac. 3) Press and hold the power button for 5 seconds. How to reset SMC in a MacBook with a removable battery 1) Shut down the Mac and disconnect the power adapter.PRAM RESET Shut down the computer. Wait another 5 seconds and press the power button to turn on the computer. Attach the computers power cable.Fans will rev to full speed (which is perfectly safe) and is a result of the fan control modules not being loaded. I use Gnome as my desktop environment.What You Can Expect from Linux on your iMac G5Generally speaking, you can expect a fully functional desktop machine similar to MacOS X.However, these things will require fixes and work-arounds to get working (explained on this page):Fan/thermal control. I have no separate swap partition, but I do have a separate /boot partition (required since my root partition is encrypted). Extensive installation notes for Debian 4.0 are already available here and current problems with the installer on powerpc are listed in the errata.As a matter of interest: My system install currently exists on a small 6GB partition alongside MacOS X that is encrypted using dm-crypt with a 256bit AES key (available as an option during install).
Smc Fan Control For Power G5 Driver But ThisFor example, ?YouTube videos are unplayable (As a workaround, you can use youtube-dl). As far as I know, no one has got this to work.Adobe Flash. (I think there are open-source ATI drivers available for rev B and C machines?)Internal dial-up modem. Support for this will be available when (fingers crossed) the Nouveau project manages to reverse engineer appropriate Nvidia drivers. Nvidia provides a binary (closed source) driver but this only works on x86 machines, not ppc.This isn't dangerous to your system - but it sure is annoying! In the meantime,the fan issue is solved simply through loading up the correct fan modules and forcing them to load on startup every time. I have not figured out any way to put the screen to sleep, and the screen brightness also doesn't seem to be configurable, which is annoying because the default screen brightness for the iMac revA (Nvidia) is set quite low.This problem is solved in the latest builds of Debian Etch and will be sorted by the time Debian 4.0 is released.Fans will rev to full speed without proper control. Both suspend-to-disk (hibernate) and suspend-to-ram (standby) are not working standby is unlikely to be possible at all, a hack for hibernate is in the early stages for the G5 processor (by Johannes Berg). This is not well supported. The iMac G5 uses System Management Unit (SMU) rather than the more common Power Management Unit (PMU) for its general power management. Gnash is a project rapidly hacking an open source alternative and will soon make this functionality possible.Power Management: Hibernate, Standby, Screen Sleep, Screen Brightness. Use windows on mac for development with visual studioEdit the file which describes what is mounted on start up.4. Make a directory to mount your partition into:Sudo mkdir /mnt/mac (you can call the folder whatever you like)3. In Gnome, go Desktop > Administration > Disks and note the device name of your disk (something like /dev/sda4).2. These will both change depending on your own circumstances.1. "/dev/sda4" specifies the partition you are mounting, and "mnt/mac" is the directory you are mounting it in. This is either hfs or hfsplus depending on the partition. If I were mounting an hfsplus partition I would add "ro" to the options, becoming "defaults,user,ro" to make the partition read-only. The fourth part is the mount options what I have described above is a default mount, that is able to be done by the user. The third is the file format which could be, again, hfs or hfsplus. The first part is the device, the second is the directory you've created to mount the partition into.
0 Comments
Leave a Reply. |
AuthorJill ArchivesCategories |